What is the difference between QSFP 28 and QSFP+？

QSFP28 (Quad Small Form-factor Pluggable 28) and QSFP+ (Quad Small Form-factor Pluggable Plus) are both types of transceiver modules used in high-speed network applications. The main difference between the two lies in their data transmission speeds and the interface they are designed for:

1. Data Rates: - QSFP28 supports data rates of up to 100 Gbps per port, allowing for a total throughput of 400 Gbps when used in a 4x100G configuration. - QSFP+ supports data rates of up to 40 Gbps per port, allowing for a total throughput of 160 Gbps when used in a 4x40G configuration.

2. Interface: - QSFP28 uses a 28Gbps electrical interface, allowing for higher speed and better performance. - QSFP+ uses a 10Gbps electrical interface, which limits its data transmission capacity compared to QSFP28.

In summary, QSFP28 is designed for higher data rate applications compared to QSFP+, making it suitable for use in modern high-speed networks and data centers.

Form factor & connectors

The term "form factor" refers to the standardized size and shape (or“footprint” of the optic, but other design features also help create each standard's definition. While there are many different transceiver form factors to consider, a few standards are more universal than the others.

Which you need is primarily determined by what form factors are compatible in the switch or router the optic is to be plugged in to, so it is always good to check what your system accepts.

AddOn's SFP-10G-SR-S-AO Cisco Compatible 1G SFP+ 40km LC Transceiver

Without the right form factor for your network environment, the optic may not fit into your switch or router at all. If it does connect, it may have impaired performance.

Can I use 100G QSFP28 port based with 40G QSFP+ transceiver?

eci-10gig-migration-to-40gbe-using-mtp-harness-cable-and-mtp-trunk-cable.png

Most Switches, Network Packet Broker (NPB), and other Network Element allow the use of 40G QSFP+ optics within QSFP28 slot to support 10G using fanout/Breakout cable or 40G Multimode straight conectivity using MTP to MTP fiber cable.

SFP vs SFP+ vs XFP vs QSFP+ vs CFP vs QSFP28 Differences

Through the above definitions of each type of fiber optic transceiver module, you may have a further understanding of them. Now, we are comparing these transeiver one by one.

SFP vs SFP+ (SFP+ vs SFP): Simple to understand, SFP+ is an updated vision of SFP. SFP usually support 1.25Gbit/s to 4.25 Gbit/s while SFP+ supports data rates up to 10 Gbit/s. When it comes to SFP vs SFP+, they have the same size and appearance, but in a different standard which SFP is based on IEEE802.3 and SFF-8472.
SFP+ vs XFP (XFP vs SFP+): In comparison to earlier XFP modules, SFP+ modules leave more circuitry to be implemented on the host board instead of inside the module. The size of SFP+ is smaller than XFP, thus it moves some functions to motherboard, including signal modulation function, MAC, CDR and EDC. XFP is based on the standard of XFP MSA while SFP+ is compliance with the protocol of IEEE 802.3ae, SFF-8431, SFF-8432.
SFP+ vs QSFP+: QSFP+ has four-channel SFP+ interfaces which can transfer rates up to 40Gbps. And of course, they have different standards.
CFP vs QSFP+: QSFP+ (Quad Small Form-Factor Pluggable Plus) modules offer customers a wide variety of high-density 40 Gigabit Ethernet. The CFP is a hot-pluggable transceiver module form factor that supports a wide range of 40Gb/s and 100Gb/s applications such as 40G and 100G Ethernet.